Introduction Siemens (Сименс) доставка по России со склада и под заказ

	Device	Notes	Size
			1	2	2.5	3	4
I2_6085	Empty enclosures	Enclosures with spring-mounted quick-release locks, which are opened with tools and closed by hand. Knockouts for flange openings and cable entries. Components for the enclosure are delivered separately.	Mounting depth 147 mm: 8HP2 001 ≠ 8HP2 021 ≡	Mounting depth 147 mm: 8HP2 002 ≠ 8HP2 022 ≡ Mounting depth 212 mm: 8HP2 012 ≠ 8HP2 032 ≡	Mounting depth 147 mm: 8HP2 027 ≠ Mounting depth 185 mm: 8HP2 047 ≠	Mounting depth 147 mm: 8HP2 003 ≠ Mounting depth 239.5 mm: 8HP2 023 ≡	Mounting depth 147 mm: 8HP2 004 ≠ Mounting depth 239.5 mm: 8HP2 024 ≡
I2_6086	Enclosures		8HP1 101	8HP1 102	8HP1 107	8HP1 103	8HP1 104
I2_6087	Cover / intermediate frame		8HP1 201 ≠ 8HP1 221 ≡ with one actuating flap: 8HP1 331 ≠	Mounting depth 147 mm: 8HP1 202 ≠ 8HP1 222 ≡ Mounting depth 212 mm: 8HP2 212 ≠ 8HP2 232 ≡ with one actuating flap: 8HP1 351 ≡ with two actuating flaps: 8HP1 352 ≡	Mounting depth 147 mm: 8HP2 227 ≡ Mounting depth 185 mm: 8HP2 247 ≡	Mounting depth 147 mm: 8HP1 203 ≠ 8HP1 223 ≡ For increasing the mounting depth by 92.5 mm: 8HP1 283 with three actuating flaps: 8HP1 353 ≡ with four actuating flaps: 8HP1 354 ≡	Mounting depth 147 mm: 8HP1 204 ≠ 8HP1 224 ≡ For increasing the mounting depth by 92.5 mm: 8HP1 284
I2_6088	Mounting plates		8HP6 301	8HP6 302	8HP6 307	8HP6 303	8HP6 304
I2_6089	Meter panels	with meter fixing screws	--	--	with one meter panel 8HP6 111	with one meter panel 8HP6 112	with two meter panels 8HP6 112
I2_6090	Assembly kits for modular installation devices with snap-on mounting	with cover plates; with one N bar, one PE bar, both 6 mm x 6 mm, and one incoming terminal, 35 mm²; the required terminals must be ordered separately (8WA2 860 4 mm²)	one tier with 14 MW: 8HP5 531	two tiers, each with 14 MW: 8HP5 532 (tier spacing: 125 mm)	three tiers, each with 14 MW: 8HP5 533 (tier spacing: 125 mm)	four tiers, each with 14 MW: 8HP5 534 (tier spacing: 125 mm)	--
I2_6091	DIAZED or NEOZED fuse assembly kits	with bus-mounting fuse bases and cover plates; with N and PE bars, 6 mm x 6 mm; with incoming terminal, 35 mm², as well as one outgoing terminal per 3-pole circuit	2 x 3 x 25 A: 8HP5 142 2 x 3 x 63 A: 8HP5 162	4 x 3 x 25 A: 8HP5 144 5 x 3 x 25 A: 8HP5 145 4 x 3 x 63 A: 8HP5 164 2 x 3 x 25 A and 3 x 3 x 63 A: 8HP5 170 8 x 3 x 63 A: 8HP5 157 (NEOZED fuse links)	7 x 3 x 25 A: 8HP5 147 6 x 3 x 63 A: 8HP5 166 5 x 3 x 25 A and 2 x 3 x 63 A: 8HP5 172 2 x 3 x 25 A and 4 x 3 x 63 A: 8HP5 171	8 x 3 x 25 A: 8HP5 148 10 x 3 x 25 A: 8HP5 150 8 x 3 x 63 A: 8HP5 167 6 x 3 x 25 A and 4 x 3 x 63 A: 8HP5 174 7 x 3 x 25 A and 3 x 3 x 63 A: 8HP5 175 2 x 3 x 25 A and 8 x 3 x 63 A: 8HP5 173	--
I2_6092	Assembly kits with LV HRC fuse bases	Connections: NH00 clamp connections NH1 M10 terminal screws NH2 M10 terminal screws NH3 M12 terminal screws without N and PE terminals	8HP5 300	8HP5 301 8HP5 302 8HP5 312 8HP5 314	8HP5 311 8HP5 312 8HP5 314	8HP5 312 8HP5 314	--
I2_6093	Assembly kits for fuse switch disconnectors	without cover plates, fixing screws for the switch disconnectors are included in delivery	8HP5 413 ¹⁾ 8HP5 411 ³⁾	8HP5 414 ³⁾ 8HP5 415 ²⁾ 8HP5 421 ¹⁾ 8HP5 422 ³⁾	8HP5 415 ²⁾ 8HP5 421 ¹⁾	8HP5 422 8HP5 423 ³⁾ 8HP5 424 ³⁾	--
I2_6094	Cover plates for enclosures with switch disconnectors	for covering the enclosure opening with degree of protection IP2x, sealable	8HP6 431 8HP6 422	8HP6 432 8HP6 423 8HP6 404 8HP6 424 8HP5 427 8HP5 406	8HP6 423 8HP6 404 8HP6 424 8HP5 427	8HP6 428 8HP6 406 Terminal cover: 3TX6 546-3B	--

≠ opaque cover

≡ transparent cover

¹⁾ PEN terminals can be installed.

²⁾ PEN terminal installed.

³⁾ 4 and 5-conductors must be passed through uncut.

Область применения

It is suitable for use in all industrial and commercial areas, in power plants, large public and private buildings, public utility companies, as well as office and residential buildings.

The components of the 8HP distribution system comply with the requirements of type-tested low-voltage switchgear assemblies (TTA) to EN 60439-1/DIN VDE 0660 Part 500. The enclosure complies with the protective measure "Total Insulation" according to DIN VDE 0100.

Standards

DIN VDE 0660 Part 500

Specifications for type-tested low-voltage switchgear assemblies (TTA)

DIN VDE 0110

Specifications for rating the creepage distances and clearances of electrical equipment

IEC 60439-1

Ready-made controlgear assemblies for low voltage

DIN VDE 0660 Part 107

Specifications for low-voltage controls

DIN VDE 0100

Specifications for the erection of power installations with rated voltages of up to 1000 V

Declaration of conformity

This declares conformity of the components and distribution boards with the safety requirements for low-voltage equipment as specified in the EU Directive dated 19.02.1973.

Special tests

Fire tests for equipment used in mining are performed by the Versuchsgrube Tremonia, Dortmund, Germany.

Shock tests for equipment used in protective rooms are performed by the Bundesamt für Zivilschutz, Bad Godesberg, Germany, regulation category RK 1.0/10 to safety level "A", certificate of use 036/95.

Earthquake tests are performed by the IAB, Ottobrunn, Germany. Tests for use in EX zone 2 (special version).

Zone 2 is an area where a potentially explosive atmosphere, such as a mixture of air and combustible gases, vapors or mists, is not likely to occur in normal operation, or only for very brief periods.

The enclosure is UL-certified.

Installation conditions

Installation	Climatic conditions according to DIN 50010	Special operating and ambient conditions
Indoor installation	An indoor climate is an environment in rooms that are designed so that objects are largely separated from the direct influence of an open-air climate.	If the operating and ambient conditions differ from the standard conditions to DIN VDE 0660 Part 500, Item 6.1, appropriate measures must be taken to protect and maintain the operating capability of the controlgear combination for "Special operating and ambient conditions" according to Item 6.2 (mechanical protection, ventilation, indoor heating, breathers, etc.).
No further measures necessary.
External installation	An external environment is an environment in rooms that are designed so that objects are protected against direct sunlight and precipitation and, if necessary, against wind, but are otherwise exposed to an open-air climate.
Measures: e.g. protected erection or protective cover, if necessary with additional walls and door (protective cabinet).
Outdoor installation	An open-air climate is an environment that affects objects in the open air.
Only permissible with the measures described for external installation.

Conversion from Pg to metric screw connections

We tested a new option for using metric screwed connections with the 8HP molded-plastic distribution system. The results of this test showed that the Pg openings listed in the following table are also able to accommodate metric screw connections. Metric screw connections with lock nuts are used. Appropriate sealing washers are used in order to ensure degree of protection IP65.

The values for the tested conversions from Pg to metric screw connections are shown in the following table.